Here is the AFTER photo: *My very first tutorial* Woot-woot~
Here is an EASY-PEASY tutorial on how I did it:
I wiped the whole thing down with a wet towel to remove all the flaking paint and dust and in keeping with my shabby chic style-- painted the whole thing white. I didn't sand anything on the dresser, figuring on using those bits of globby paint to my advantage when antiquing it later. Once painted, I wanted to add some of those wooden appliques that everyone is just wild about....but heck, it is just a flimsy one dollar dresser, so that seemed absurd. Soooooooooo I got out one of my many stencils and I set out to stencil on some joint compound to give it the "appearance" of a wooden applique.
Firstly, your needing some joint compound, a putty knife (I use a stir stick instead), a stencil of your choice, some tape, a ruler & pencil. Thats it~ Next, if your centering your design like I did-- find the center and mark the spot with a pencil to help you align your stencil... next, just tape your stencil down. (yes, that is paint on my stencil, I do not wash the paint off of my stencils)Now, comes the fun part. You just take some of your joint compound and spread a nice coat of it on top of your stencil. No worries, don't stress-- it does end up looking fabulous-- promise! While this is setting up a little, I draw the center on the next drawer...so I would say about 2 minutes max. That seemed to work fine for me~ Next, you just pull up your stencil. Keep a good grip on it as its going to be heavy with the excess joint compound on it. (Place the stencil onto newspaper or scrap paper so you don't get anything on your work surface) If for any reason your not happy with the results, simply wipe off the joint compound while it is still wet, with a wet paper towel, and start over! (I had to wipe off a finished drawer as I noticed I had applied the stencil upside down lol) At this point you want to tap down any large peaks or wipe away any mistakes or globs. Again, no biggy-- enjoy the process~ When your ready for the next drawer, simply pick up your joint compound ladden stencil and reapply to a new drawer front. You do not have to clean your stencil between each drawer...unless your extremely messy and it is necessary! Repeat this process until all the drawers are completed. Let the newly appliqued pieces dry for 5 hours or more....until everything is dry to the touch. At this point you can either use your nail or an razor blade to cut off any bumpy bits --if you want to. Don't sand it or it will crumble completly off. To clean your stencil, simply scrape off remaining joint compound and put back into the container. Try to wipe off as much of the compound as possible (I use toilet paper, it is softer and less harsh on the stencil than paper towels) and toss the tissue into the trash. Just rinse the stencil under hot water while rubbing the stencil gently and the joint compound washes away. Next, I painted over the raised area with the same latex house paint that the drawers had been painted with. I put two coats on each drawer, once the paint has dried comes the super fun part! Antiquing! I used a nutmeg brown paint watered down and applied randomly with a large brush. I then used my fingers to rub the watered down paint all over the piece. I had to rewet my fingers a lot to keep the paint moving in an even coat. If it sets up and looks awful-- just rewet the area and run your fingers/hand across it until you like the looks of it.Looks good huh? If at a later date I feel I want it to be lighter, I'll just wet it and rub more off. Lastly, just take a brown ink pad.... I used a color called "chocolate chip" and rub it along the edges and raised areas of your piece. This is when the piece really comes to life. Here is my one dollar dresser all finished with its new knobs and freshly appliqued painted surfaces ready to be used once again! (I bought a bag of 24 of these knobs for $2 bucks) Here is a close up. Doesn't it look neat and super old? Not to bad for a dollar dresser~
0 comments:
Post a Comment